Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replace the standard rubber bow roller on your boat trailer with this blue thermoplastic rubber version from Yates. TPR material is stronger than rubber and softer than polyurethane, and it won't leave marks on your boat.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
What's up everybody, it's AJ with etrailer.com. Today we'll be checking out the Yates bow roller. So this is going to be a replacement part that goes right here on the front of your trailer. Let's say yours is worn down or it's not spinning like it's supposed to anymore because it's been out in the weather so long. It's an easy part that you can replace and get back up, running as new. Let's check it out.
Now what this is gonna do, is it's gonna go right here on your trailer and you can roll it, so that means when you're pulling your boat on there, and let's say the bow hits it, it's gonna roll up like that and it'll be just fine, it'll roll all the way. Acts as a stopper too, so as it hits this, it's better than it hitting the trailer and scratching up your boat. Also, when it's just sitting on there and you've got to tie it down, if your boat is to move and travel up and down, it's gonna hit this instead of the metal parts of your trailer, so that's, again, just gonna save your boat from getting all scratched up and damaged. It's made out of a thermal plasticized rubber. So it's gonna be a little more soft than regular polyurethane and has a little more of a structure than rubber does, so it's a nice in the middle of both of those.
I also wanna point out that the material it's made of isn't gonna leave marks on your boat. So some of the other ones, if it was just made rubber, and you we're to come up here, pull your boat up and hit it kind of hard, it might leave black marks here on the bottom of your boat. This isn't gonna happen with this one, there's not going to be any scraps or issues. Now I'll give you some measurements. It's going to be three inches and three quarters long, that's the width here.
And then it's also gonna have a diameter here where the hole where you gonna put the bolt in is going to be a half inch. So that way you can just get the right hardware to make sure it's gonna go through your trailer and your roller. Now you also can get these in a couple different colors, they also will come in blue and black. So if you don't want the yellow one that we we're installing today, there's two other options at might match your boat trailer a little bit better. It's really easy to install.
You just take this bolt out. Check out how we did it, Ready to install our new roller here, we're just going to set it into place. We're gonna use the existing hardware from the old one that we took out. Just slide it through the holes in the middle, mash it up on the other side. Now, something that would suggest is if you aren't getting ones with the bells on the side, and you see this the old one we took off. It did have those, so this bolt's a little longer than it should be so it's gonna stick out. You can get different sized hardware to run through that where there's not as much sticking on both sides, but this will still work like this. So we have the washer on this end, push there, and then we're gonna put a washer and nut on the other side. Just gonna get started by hand and I'll come back with tools and tighten it down. Got a ratchet and a wrench on here, just need to go ahead and tighten it down. So I went in, tighten it down, made sure the bolt head and nut here are tight, but this can still freely spend 'cause we're gonna need that when you go to put the bolt on. Overall, super easy to replace and get this part back up and running. and I liked this one because it's not gonna scuff up the boat either. So you don't have to worry about making any marks and now this rolls like it was supposed to again, it's gonna all work with that trailer and make it easier to get that boat up there. Well, I think that does it. Thanks for hanging out. I hope this helped..
Average Customer Rating: 4.8 out of 5 stars (94 Customer Reviews)
Replace the standard rubber bow roller on your boat trailer with this blue thermoplastic rubber version from Yates. TPR material is stronger than rubber and softer than polyurethane, and it won't leave marks on your boat.With this roller having a drop/lip about 1-1/8" in from the edge on both sides, our boat will rub on both sides as it comes up on the roller. Do you have a roller that is a smooth transition from the edges to the center? The 4" fits, but not the drop/lip coming to the center of the roller from each side. We would like to return it and get a different one if you have what we are looking for.
Thank you for your time
I am a trailer sailor and always looking for ways to make the task of raising the mast easier. I am in the middle of creating a roller stabilizer A frame to keep my 30' mast from wandering to either side while raising it. This roller is part of my new system and I expect it to keep the mast centered upon lifting. However, it is still snowing here in The Rockies so the actual test is going to have to wait a while longer.
Michael
4/23/2024
After some revisions to the yoke that holds the roller, it seems to handle the load of raising the mast very well. Overall, a good item for my needs.
as you can see, I still have some parts to replace. But I ordered these parts at the beginning of this week. Used free shipping. Delivered Saturday, done Saturday afternoon. So easy. Looking forward to finishing this trailer. Will use etrailer again
Good product.
Exact match replacement
This was a great replacement for my old worn roller that was on my trailer and it got here quick also.
Vince
6/18/2020
holding up great still looks brand new
The roller worked perfectly for the trailer I was redoing. I also bought a couple of other parts that I needed they have great products, quick shipping and excellent customer service. Will keep buying all of my trailer parts from here
As advertised
I was very impressed with the great service, excellent products, and end results after assembling my boat trailer with the parts ordered from Etrailer. Shipping was fast. Very reasonable prices. Will definitely order thru this company again and have already referred friends of mine to have them take a look at your site.
Product was exactly as described. The exact measurements of the product where very helpful, in fact that is why I bought from etrailer. Other websites did not provide as detailed information.
I plow plastic pipe into the ground for livestock water. I bought these puppies to be pipe guide rollers on my cat dozer. They will keep the pipe in alignment as it comes off the spool and guide it into the ripper boot. Each spool has 2,000 ft in it. The first job is six miles long. Should work like a champ!
The Bow roller and tail light converter arrived promptly and in exactly as described. The tail light converter is a blessing. My 1998 Toyota 4Runner now throws the correct signals to my boat trailer. Yeehaw!
Great product and a great price. Shipping was fast. Upgrading my boat trailer and the existing bow stop was beat up from power loading. Now with parts from etrailer it is looking like new again.
A great bow roller at an excellent price.In fact , I need 2 more 4 inch keel rollers ( blue ) that I hope they can sell me. This is a great place to get all of your trailer needs !!!
Product will function as expected but the quality of the finish is not what I expected. Many scuffs and imperfections.
David
10/9/2022
After one year this roller is still soft and has not marked my boat. Happy with purchase.
The part came quickly, easy to install, has proved to be very sturdy, and does not mark up my sailboat hull.
Perfect fit replacement
Thanks
Dave
7/4/2016
Excellent
My order came quickly and everything I ordered was in the same box. I installed everything yesterday. Etrailer was easy to do business with I will be back
Relly nice roller. Fits the shape of my bow mauch better then the old straight V type. I highly recomend these rollers and E Trailer.
Perfect replacement,,, better than the original. Care was taken when packaging and shipping was very timely
Really liked the color at first,but the roller mars real bad and now looks awfu. I;m going to replace the the roller soon. tired of it looking this way....
Bow Roller and bell are showing some signs of color fading, otherwise they're in good condition.
Product works as advertised. I'm changing regular rubber bow roller because was making black marks on my boat for this product that does not leave marks and does the job perfectly.
We received this bow roller soon after it was ordered and are completely satisfied with it. It replaced our broken-old one with ease and simplicity. Thanks!
I love this product. No more rubber marks on my white hull, and they were an exact replacement for the old ones.
Do you have a question about this Boat Trailer Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Brooke M.
1/4/2024
Part # YR4174-4 would be a better fit. It is still four inches long but doesnt have any differing grooves. Its all one smooth angle. I can have our customer service team reach out.